|
Product Details:
|
| Power: | AC220V±10% 50Hz | Plastic Testing Machine: | Melt Flow Index Tester |
|---|---|---|---|
| Temperature Rangeradius: | 400℃ | Temperature Accuracyblade To Jawand Dust Collector: | ±0.2 ℃ |
| Display Resolution: | 0.1℃ | Maximum Comsuption: | < 600W |
| Temperature Recovery Time: | Less Than 4 Min. | Name: | LCD Plastic Testing Machine , PLC Melt Flow Rate Tester Manufacturer |
| High Light: | impact test equipment,material testing equipment |
||
LCD Plastic Testing Machine , PLC Melt Flow Rate Tester Manufacturer
Purpose:
Melt flow rate tester (also known as melt index meter) was measured under certain conditions thermoplastic melt flow rate of the special equipment. With the determination of melt flow rate MFR, measured melt volume rate MVR, measured melt density ρ, measured melt flow rate ratio FRR and other functions, this machine high precision temperature control, key parts nitriding treatment, high strength and hardness , small deformation accurately measure the flow rate which provides a good condition.
Brief introduction
HD-R804-1 type with industrial PLC programmable controller, LCD operating platform, temperature part is separate temperature unit, LED digital display. Automatic temperature control aircraft from the operating method is divided into manual, time control, automatic three cut material way, to achieve Quality Act (MFR) and the volumetric method (MVR) two kinds of test methods; aircraft to the measured temperature of the test material the melt density, the system also has the temperature calibration.
Principle:
Thermoplastic melt flow rate (melt index) is plastic at a temperature and load, the melt every 10 minutes through a standard capillary die quality or melt volume, with MFR (MI) or the MVR value, which can distinguish thermoplastic adhesive in the molten state flow characteristics. For thermoplastics and chemical fiber raw materials, quality assurance of products and other products of great significance.
According to the standard:
Electronic MFR Plastic Melt Flow Index Testing Instrument reference standards: ISO 1133, ASTM D1238, JIS-K72A, GB/T3682, JB/T5456, JJG 878
The main technical parameters:
Measuring range :0.1-800 .00g/10min (MFR) 0.1-800.00 cm3/10min (MVR)
Temperature range: room temperature -450 ℃
Temperature accuracy: ± 0.5 ℃
Timing accuracy: 0.1S
Displacement accuracy: 0.01mm
Load: full load
Material cutting modes: manual, time control, automatic
Barrel diameter: 9.550mm ± 0.025mm
Barrel Length: 160mm
Die: made of tungsten carbide, length: 8.000mm ± 0.025mm diameter: 2.095mm ± 0.005mm
Power: 0.45KW Power supply: AC220V, 50Hz
Instrument Size: 400mm × 500mm × 600mm
Instrument Weight: 65Kg
Specification:
|
Machine size(W*H*D) |
250*510*350mm |
|
Power |
AC220V±10% 50Hz |
|
Barrel parameters |
Inner hole 9.55±0.025mm |
|
Pistons parameters |
Piston head: 9.475±0.015mm |
|
Piston length |
H=6.35±0.1mm |
|
Paramters |
Extrusion hole 1=2.095±0.005mm |
|
Temperature parameter |
With intelligent temperature control instrument, with four pairs of significant temperature setting control, PID parameters can be automatically set, precision up to ± 0.1 degree centigrade |
|
Temperature rangeradius |
400℃ |
|
Temperature accuracyblade to jawand dust collector |
±0.2 ℃ |
|
Display resolution |
0.1℃ |
|
Maximum comsuption |
< 600W |
|
Temperature recovery time |
less than 4 min. |
|
Weight parameters |
|
|
Weight accuracy |
±0.5% |
|
Basic configuration |
0.325kg, 1.2kg, 2.16kg, 3.8kg, 5.kg, 10.0kg, 12.kg, 21.6kg |
|
Position detection |
|
|
Loop distance from up and down |
30mm |
|
Control precision |
± 0.1mm |
|
Test flow control |
|
|
Times of cutting the material |
0~10 times |
|
Material cutting interval |
0~999s(set reference Table 2) |
|
Control flow reaches the set temperature without volatility |
|
|
Barrel temperature time |
15 min. |
|
Material be installed |
1 min |
|
Material sample temperature recovery time |
4 min. |
|
When binder set |
1min |
Pictures:
Contact Person: Victoria Li
Tel: +8613809275028
Fax: 86-769-28682030
